Toyota Tacoma Front Door Image Dynamics CTX65CS / ID65CS Component Speaker Installation Kit
This is our number one selling component speaker setup. It is an amazing “bang for buck”. The Image Dynamics CTX65CS Component Speakers are the affordable solution for the sound enthusiast seeking a high performance speaker system. Their high efficiency provides incredible detail and very high output levels while producing rich well-balanced sound with excellent tonal characteristics. More than the sum of the parts, the CTX65CS components feature a long excursion mid-woofer design that handles high-power amplifiers effortlessly with low distortion allowing higher output levels. The Silk dome CTX65CS tweeters deliver the dynamics and detail without listening fatigue or harshness.The CTX65CS components performance is the product of proper materials and a well executed engineering design. This translates to neodymium magnet silk dome tweeters with swivel mount, mica-polymer composite cones that are stiff, yet light and well-damped butyl rubber surrounds. Crossover with 250 volt metalized polypropylene capacitors air core inductors and 3 position tweeter level control.
This kit includes discounted pricing on the following items needed to install the Image Dynamics CTX65CS speakers in the front doors of your Toyota Tacoma:
2 – Image Dynamics CTX65CS Mid Range Drivers
2 – Image Dynamics CTX65CS tweeters
2 – Image Dynamics Crossovers
2 – Front Door 6.5″ speaker mounts (Driver & Passenger Side) – this is a pair of speaker mounts.
2 – tweeter mounts – custom sized.
8 – Mounting Bolts
8 – Mounting Screws
2 – Speaker Wire Harness Kit
2 – Tweeter Wire Harness Kit
2005 – 2015 (Generation 2) Tacoma – If you are installing our plug and play amplifier(s), we highly suggest using the tweeter harness adapters (as shown in installation video below). The crossover mount adapters make it easier to mount your crossover below the door panel You can use zip ties to accomplish the same task.
2016 – 20xx (Generation 3) Tacoma -If you are installing our plug and play amplifier(s), we highly suggest using the tweeter harness adapters AND the speaker harness adapters (as shown in installation video below). The crossover mounts is not required since you will be installing the crossover inside the vehicle. Be sure to watch the video below.
If you are planning to power your speakers with the stock wiring (using the stereo to power the speakers), you will want to add the speaker wire harness adapter kit to your order. This kit will allow you to plug into the the factory wiring without any cutting of splicing AND will make it much easier to return your Toyota Tacoma back to factory if you ever trade in or sell. If you are planning to install an amplifier, you will be running heavier gauge speaker wire to your speakers so you will NOT need wire harnesses.
Thank you for taking the time to check out our products for your Toyota Tacoma. We sincerely appreciate the opportunity to do business with you!
Mid Range Drivers:
Frequency Responses: 55Hz – 25Khz
6.5″ Component Speakers
100 Watts RMS (each speaker / component set)
Mounting Depth: 2.85″
Mounting Diameter: 5.6″
100 Watts RMS
Mounting Depth: .875
“Mounting Diameter: 1.899
NOTE: The included crossover MUST be used in the installation. Failure to use the crossover will result in speaker damage that is not covered under warranty. We have powered these speaker in show vehicles with 140 watts for over 7 hours of continuous play time. These are amazingly loud and clear. Be sure your amp is providing CLEAN power.
Manufacturer’s Warranty: 1 year.
Below are instruction on how to install the speakers using your stock wiring. If you are using our plug and play setup, you will probably install them similar to the video below. If you are running new speaker wire, you will probably install your crossovers either in the center console or in your storage compartments under the rear seats.
2005 – 2015 Component Speaker Installation
2016+ Component Speaker Installation
How to remove the door panels: