2020-2023 Toyota Tacoma Add amplifiers to factory stereo Plug & Play Harness Sound Processor Factory Integration

$19.99

Add amplifiers to a 2020-2023 Toyota Tacoma (non-JBL) in hours, not days. Plugs into the factory head unit and wiring with no cutting or new speaker wire.

  • Non-JBL only – not compatible with factory JBL systems
  • Connects behind the factory head unit
  • Example installs, wiring diagram and videos in the description below

SKU: A3-77-EZAH10-3A Category:

Description

Upgrade your Tacoma audio system in hours, not days, with this plug-and-play amplifier factory integration harness. Skip the messy wiring and complicated installs – there’s no need to run new speaker wire to the doors and dash.

The harness plugs directly into your factory head unit and existing wiring, so you can add one or more amplifiers without cutting or splicing a single factory wire. The install is completely reversible.

Check out our other Tacoma plug & play harnesses – they make installing aftermarket speakers fast and easy with zero cutting or splicing.

Amp / Sound Processor Harness 1 & 2

Harness 1 – 18 gauge LOC / DSP signal wiring
Harness 2 – 16 gauge amplifier output wiring
  • 17 ft leads – 272 ft of total wiring included (17 × 16)
  • Harness 1 – 18 gauge signal wire – connects to your LOC / DSP / sound processor
  • Harness 2 – 16 gauge speaker wire (thicker than 18G) to handle the extra power – connects to your amplifier’s speaker output
  • Industry-standard 12V color-coded Molex input/output connectors for a plug-and-play system
  • Easily modified to work with just about any aftermarket amplifier

Note: This harness system is built to work with Taco Tunes plug-and-play amplifiers. You can cut off the blue/black Molex plugs and connect other amplifier brands, but because there are so many amp brands and models, we can’t help with that install. To make it easier, the color and purpose of every wire is listed in the wiring schematic below.

Does not support factory-installed JBL audio systems.

Important: The factory wiring wasn’t designed for a lot of power. We don’t recommend more than 100 watts RMS on stock wiring. Most amps are rated at 14.4 volts, while the Toyota charging system runs at 13.6 volts, so an amp rated at 100 watts RMS is fine. We highly suggest a quality LOC / DSP / sound processor.

Remote Turn-On / 12V Constant Wires (Harness 3)

2020+ Toyota Tacoma remote turn on and 12V constant plug and play harness
2020+ Toyota Tacoma remote turn-on and 12V constant plug and play harness

This harness provides 12V constant power for your LOC / sound processor, plus an accessory wire that turns your aftermarket audio gear on and off.

  • Red – accessory remote turn-on / turn-off
  • Yellow – 12V constant, used to power your LOC / DSP / sound processor. Do not use it to power an amp or powered sub.

Note: All amps and powered subwoofers need fused power run directly from the battery. A relay might be needed when using two or more amplifiers.

Install Videos

How to add amps using Taco Tunes NTUNE6
How to add amps using AudioControl LC5i Pro

Wiring Schematic

SpeakerPositive (+)Negative (−)
Left frontWhiteWhite/Black
Right frontGrayGray/Black
Left rearGreenGreen/Black
Right rearPurplePurple/Black

The same colors are used on both harnesses:

  • Harness 1 – blue plugs / cut end (input from the stock stereo to your LOC / DSP).
  • Harness 2 – black plugs (amplifier output to speakers): connect directly to our TXD line of amplifiers, or remove the plugs to integrate just about any aftermarket amplifier.
  • Harness 3: Red = remote turn-on; Yellow = constant 12V (for sound processors only – do not use to power amps).

Product Terms

  • This harness provides 4 output channels (LF, RF, LR, RR) from the stock head unit. I understand I will need to supply an LOC / DSP / sound processor that outputs the 4, 5 or 6 channel low-level signal my amplifiers need.
  • I understand that not all LOC / DSP / sound processors work properly with my stock head unit (radio).
  • I understand this product is non-refundable once the packaging is opened. No exceptions.
  • I understand support for this product is limited to making sure the signal reaches my LOC / DSP / sound processor. Taco Tunes can’t support processors or amplifiers bought from other vendors.
  • Note: We suggest the NTUNE6 or a similar product designed for Toyota stock stereos. Lower-end LOC units often cause “newer model” head unit errors and/or head unit shutdown issues.