2007-2021 Toyota Tundra Stock Amp Replacement Rack

$139.99

-

Custom 14 gauge amp rack for 2007-2021 Toyota Tundra (non-JBL) that mounts our plug and play amps in the stock amp location, with no drilling or cutting.

In stock

Description

The bolt-in home for your Tundra amps

Zero cutting. Zero drilling. This 14-gauge steel rack bolts to the factory mounting points under your passenger seat and gives your amp and DSP a solid, factory-clean home.

  • 14-gauge laser-cut, CNC-bent steel
  • 100% bolt-on and 100% reversible
  • Fits 2007–2021 CrewMax, Double Cab and Regular Cab

In the box

  • 114-gauge ARTUN07 amp rack, laser cut and CNC bent
  • 10Mounting screws
  • 10Flange bolts
  • 2Snap bushings (grommets)

Every hole has a job

Laser cut and CNC bent to match your Tundra’s factory bolt pattern, so the rack drops in and lines up. Here’s what you’re looking at.

Top-down view of the Tundra amp rack showing slotted feet, amp mounting slots, wire pass-through holes and the clearance notch
  • A

    Bent legs with slotted feet

    The feet land on your Tundra’s stock mounting points. Slots line up with the factory bolts, so nothing gets drilled.

  • B

    Amp mounting slots

    Pre-cut for Taco Tunes TXD amps: a single 5-channel, or a 4-channel and a sub amp side by side. Running another brand? See below.

  • C

    Wire pass-throughs

    Large openings route power, ground and signal between the amp deck and the tier underneath.

  • D

    Taco Tunes amp holes

    More pre-cut holes matched to our TXD amplifiers, so they bolt on with no drilling.

  • E

    Clearance notch

    Cut to clear factory hardware so the rack sits flat and solid.

Stop screwing expensive amps into your floorboard

You put real money into amplifiers and processors to make your Tundra sound incredible. Don’t ruin that investment with a sloppy, unsafe install.

The usual way

  • Screws through the cab floor, where fuel lines, brake lines and factory harnesses run
  • Amp screwed to bare sheet metal, inviting electrical noise and buzz
  • Amp loose on the carpet: overheating, rattles and moisture damage
  • Holes and scars that stay when you sell or trade in

With the Taco Tunes rack

  • Bolts to factory mounting points, with no drilling into the floor
  • Amp sits on a rigid steel deck, isolated from the floor pan
  • Lifted off the carpet so the heatsink gets airflow
  • Unbolts in minutes with no trace it was ever there

Built like a tank

Forget flimsy universal brackets, warping plastic boards and MDF planks that soak up moisture and rot.

Heavy-duty 14-gauge steel

Thick and rigid. Even a heavy multi-channel or monoblock sub amp won’t make it flex, sag or vibrate, including on rough trails.

Precision laser cut

Every rack is cut to the exact contours and bolt pattern of the 2007–2021 Tundra, then CNC bent, so every one fits the same.

Cooler, cleaner power

Lifting the amp off the carpet lets air move around the heatsink, so your system runs cooler, louder and longer without dropping into thermal protection.

“Don’t let anyone drill holes in your baby.”

Our rule for every Tundra that rolls into the shop

Low side view of the Tundra amp rack showing the raised steel deck on bent legs
Side view: the deck rides on bent steel legs, leaving room underneath
End of the Tundra amp rack with three round wire pass-through holes
Three pass-throughs on the end keep cable runs tidy
Tundra amp rack rear right three-quarter view
Rear-right view
Tundra amp rack angled view showing the upper amplifier deck and the space underneath for a DSP

Amp on top, DSP under the carpet

Modern truck audio relies on a DSP to tune out factory EQ curves, but finding a clean place to hide one is a nightmare. The rack gives you two levels.

Upper tier

Your amplifier mounts on the top deck, with easy access to gains, crossovers and terminals whenever you want to fine-tune.

Lower tier

Mount your DSP underneath, hidden below the factory carpet and protected from boots, cargo and spills, with signal cables kept short.

Using your own amplifier?

The slots and holes in the rack are cut for Taco Tunes TXD amplifiers, so ours bolt straight on. To run another brand, you drill your own mounting holes in the rack itself, never in your truck.

Plenty of customers who build their own systems do exactly that. They have used the rack with these amps, processors and many other brands. Before you order, check your amp’s footprint against the 13.82″ × 12.46″ × 11.00″ mounting surface in the specs below.

4-channel amps

  • JL Audio JD400/4, RD400/4
  • Rockford Fosgate R2-500X4, Punch PBR400X4D
  • Alpine S-A32F, R-A90S
  • Kicker CXA360.4
  • Pioneer GM-DX874
  • Kenwood Excelon 4-channel
  • Taramps TS 400×4, TS 800×4, TS 1200×4
  • Skar Audio RP-75.4AB, SK-M4004D
  • DS18 GEN-X G1000.4D
  • CT Sounds CT-80.4D
  • Recoil RED1200.4

5-channel amps

  • JL Audio RD900/5, VX1000/5i
  • Kicker CXA660.5, LX1200.5
  • Rockford Fosgate R2-750X5, Punch P1000X5
  • AudioControl LC-5.1300
  • Alpine S2-A55V
  • Kenwood KAC-835
  • Recoil RED1800.5
  • Skar Audio RP-600.5
  • CT Sounds CT-700.5D
  • NVX VAD11005

Mono sub amps

  • JL Audio JD500/1, JD1000/1, RD1000/1
  • Kicker CXA400.1, CXA800.1, CXA1200.1
  • Rockford Fosgate R2-500X1, Power T1500-1BDCP
  • Pioneer GM-DX871
  • Kenwood KAC-9106D
  • Sundown Audio SFB and SAE series
  • Skar Audio RP-800.1D, RP-1200.1D, RP-1500.1D
  • Stinger MT-1000.1, MT-1500.1
  • Taramps BASS 800, BASS 1200, Smart 3
  • CT Sounds CT-1000.1D, CT-1500.1D
  • NVX VAD10001
  • BOSS Audio R1100M
  • Planet Audio AC1500.1M

DSPs and line output converters

  • AudioControl DM-608, DM-810, LC7i, LC2i Pro
  • JL Audio FiX-86, TwK-88
  • Helix DSP Mini
  • Match M 5.4DSP
  • Audison bit Ten, Forza
  • Kicker KEYLOC

Brand and model names belong to their owners and are listed for reference only. Taco Tunes doesn’t sell or support these products, and fit depends on your amp’s exact dimensions.

Fits every 2nd gen Tundra cab, 2007–2021

No matter which cab you drive, the fitment is dialed in.

  • Tundra CrewMax

    Makes the most of the under-seat space while keeping full rear seat function and a factory look.

  • Tundra Double Cab

    Contoured to fit without interfering with seat tracks or storage trays.

  • Tundra Regular Cab

    Turns tight behind-the-seat space into a clean, organized home for your audio gear.

One rack fits 2007–2021 Tundras, so there are no options to pick. Have a 2020 or 2021 non-JBL Tundra with factory CarPlay? The rack fits the same, and adding amps to that head unit also needs our NTUNE6 line output converter.

18 customer Tundras, one rack

Every photo here is from a customer install at our San Antonio shop, from 2013 to 2021 trucks, JBL and non-JBL. Tap a photo to read the full build.

2018 Tundra CrewMax JBL

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2020 Tundra JBL

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2021 Tundra Double Cab

System 1A. TXD1000.5 5-channel amp.

2016 Tundra CrewMax

System 1A. TXD1000.5 on the rack, ready to go in.

2015 Tundra CrewMax

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2014 Tundra

System 1B + 14.6″ head unit. TXD3204 4-channel + TXD1000.1 sub amp.

2018 Tundra CrewMax

System 1A. TXD1000.5 5-channel amp.

2013 Tundra CrewMax

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2020 Tundra

System 1A. TXD1000.5 5-channel amp.

2018 Tundra CrewMax

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2017 Tundra CrewMax

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2019 Tundra

System 1A. TXD1000.5 5-channel amp.

2021 Tundra CrewMax

Reinstalled system. TXD3204 4-channel + TXD1000.1 sub amp.

2018 Tundra CrewMax

System 1. TXD1000.5 5-channel amp.

2016 Tundra CrewMax

System 1A. TXD1000.5 5-channel amp.

2018 Tundra CrewMax

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2017 Tundra CrewMax

Reinstalled system. TXD1000.5 5-channel amp.

2014 Tundra CrewMax

System 1B + fiberglass dual 12s. TXD3204 4-channel + TXD1000.1 sub amp.

2016 Tundra CrewMax

System 1B. TXD3204 4-channel + TXD1000.1 sub amp.

2015 Tundra CrewMax

System 1B. Rack on the bench before install.

Complete the build

The rack is the foundation. Add the amps, harnesses and speakers that plug straight into your factory wiring.

Rack included

System 1 for CrewMax

Our complete plug-and-play package for the 2007–2019 Tundra CrewMax: speakers, amp, sub and harnesses.

Shop System 1

Rack included

JBL System 1B

Components, a 4-channel and a sub amp, and dual subs for JBL-equipped 2007–2021 CrewMax trucks.

Shop JBL System 1B

Rack included

Plug & play 5-channel amp kit

One amp for four door speakers and a sub, with the plug-and-play harness and power kit. Non-JBL only.

Shop the 5-channel kit

Browse

All 2007–2021 Tundra packages

Compare every bundled system for the 2nd gen Tundra, from starter setups to the Big Baller.

See all packages

Fast, frustration-free install

You don’t need a fab shop for a show-quality install. The measuring, cutting and bending are already done, so most installs take a fraction of the time of a custom mount. See exactly how it goes in before you buy.

Step-by-step install guide

Written instructions for the 2014+ non-JBL Tundra plug-and-play system.

Video walkthroughs

Mounting the amp, the rack install and amp tuning on the Taco Tunes YouTube channel.

Amps, harnesses & power kits

Plug-and-play amplifiers, the NTUNE6 and wiring for the 2007–2021 Tundra.

Ask our team

Not sure what fits your truck? Send us your year, cab and audio system and we’ll help.

Technical specifications

ARTUN07 Toyota Tundra amp rack dimensions: 13.82 inch front width, 12.46 inch rear width, 11.00 inch mounting depth
Top view with mounting-surface dimensions. Measure your amp and DSP against these before you order.
Part number ARTUN07
Vehicle compatibility 2007–2021 Toyota Tundra: CrewMax, Double Cab, Regular Cab
Material Heavy-duty 14-gauge cold-rolled steel
Manufacturing Precision CNC laser cut and formed
Mounting Direct bolt-on to OEM mounting locations under the passenger seat. No drilling or cutting.
Mounting surface 13.82″ front width, 12.46″ rear width, 11.00″ deep
Configuration Dual level: upper amplifier deck plus lower under-carpet DSP mount
Pre-cut amp mounting Taco Tunes TXD amps: one 5-channel (TXD1000.5), or a 4-channel plus a mono sub amp (TXD3204 + TXD1000.1)
Other amplifier brands Drill your own mounting holes in the rack. Check your amp’s dimensions against the mounting surface first.
Finish Black
Hardware Includes 10 mounting screws, 10 flange bolts and 2 snap bushings (grommets). The rack itself bolts down with your factory mounting bolts.

Tundra amp rack questions

Will this amp rack fit my Tundra?

It’s built for 2007–2021 Toyota Tundra CrewMax, Double Cab and Regular Cab trucks. It’s one part for all of them, so there are no options to pick.

Do I have to drill any holes?

Not in your truck. The rack bolts to the factory mounting locations under the passenger seat using the existing bolt points, so nothing gets drilled into the floor. Taco Tunes amps bolt onto the pre-cut slots. If you use another brand of amp, you’ll drill mounting holes in the rack itself.

Which amplifiers fit on the rack?

The slots and holes are pre-cut for Taco Tunes TXD amps: a single 5-channel (TXD1000.5), or a 4-channel plus a mono sub amp side by side (TXD3204 + TXD1000.1). Those bolt straight on.

Can I use JL Audio, Rockford Fosgate, Kicker or other amps?

Yes. Many customers who build their own systems mount JL Audio, Rockford Fosgate, Kicker, Alpine, Pioneer, Kenwood, AudioControl, Skar Audio, Taramps and other amps on this rack. You drill your own mounting holes in the rack, not the truck. Check your amp’s footprint against the 13.82″ × 12.46″ × 11.00″ mounting surface before you order.

How big is the mounting surface?

The ARTUN07 deck is 13.82 inches wide at the front, 12.46 inches wide at the rear and 11.00 inches deep. Measure your amp against those numbers before you order.

Can I put my DSP under the rack?

Yes. The lower tier lets you mount a DSP underneath the deck, hidden below the factory carpet, while the amp stays on top where you can reach the gains and crossovers.

I have a 2020 or 2021 Tundra with CarPlay. Does that change anything?

The rack fits the same. The difference is on the audio side: adding amps to the 2020–2021 non-JBL factory head unit requires our NTUNE6 line output converter.

Is the rack already included in your Tundra systems?

Yes. Our 2007–2021 Tundra System 1 and System 1B packages and the plug-and-play 5-channel amp kit include the steel laser-cut amp rack, so you don’t need to buy it separately with a system.

Can I take it out when I sell the truck?

Yes. Unbolt the rack in minutes and put the factory bolts back. There are no holes or scars left behind, which protects resale value and makes it lease friendly.

How long does the install take?

Because the measuring, cutting and bending are done for you, the rack itself is a quick bolt-in. Most of an amp install’s time goes into running power and signal wiring. Our step-by-step guide and YouTube videos walk you through it.

Give your amp a factory-clean home

Bolt-on, 14-gauge steel, no drilling, and it comes out in minutes if you ever go back to stock.

Additional information

Weight 3 lbs
Dimensions 12.25 × 6.5 × 2.75 in

Latest 2007-2021 Tundra Audio Installs

Real customer installs on 2007-2021 Toyota Tundras. 100% plug-and-play with ZERO cutting or splicing of factory wires!